ZLINE induction range
showing E/1
E/1 means the sensor on an induction coil has detected excessive heat.
Mon–Sat, 8am–8pm
- Surface elements and induction
- Surface element and glass top repair
- Source: ZLINE
Book a visit
Three short steps, about a minute.
or call (844) 875-7576
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E/1
actually means.
E/1 means the sensor on an induction coil has detected excessive heat. ZLINE's usual causes are poor ventilation, cookware blocking the airflow, or a long stretch at high power.
ZLINE range display · also shown as E1
What to do when E/1 shows on the rangeKind of codeSurface elements and induction
A radiant element, a coil or an induction zone did not heat the way the control expected, or ran hotter than it should. The pan, the switch behind the knob and the wiring to the element come first; on induction, the power board and the coil under the glass are checked next. A zone that will not switch off, or a crack in the glass, means the breaker goes off before anything else.
Usually leads toSurface element and glass top repair
Electric zones that stay cold, run too hot or will not switch off, and cracked or damaged glass on radiant and induction models.
Shows up asRange Error Code
The range display shows letters, numbers or a flashing symbol, beeps, and stops the oven, a cooking zone or a clean.
MakeZLINE
An American company, ZLINE Kitchen and Bath, selling professional-style gas, dual-fuel and induction ranges.
SourceZLINE Induction Ranges User Manual
Induction ranges in ZLINE's MINR and SINR families.
Before you book,
in this order.
Each step comes from ZLINE's own guidance for E/1 on its ranges. Follow it to the end: the last card says whether this is a visit.
Let the range cool and make sure its air vents are clear.
If E/1 keeps appearing with the vents clear, book a visit.
Still there?
It usually turns into surface element and glass top repair. Book with the code and the model number.
What not to do
E/1 does not mean the sensor has failed; that is F/3. Here the sensor is doing its job and reporting real heat.
What you may
notice with it.
The range problems E/1 tends to arrive with. Answer these at the range before anyone is booked.
All problems
Range Error Code
6 causes, cheapest first
Where E/1 usually leads
Surface element and glass top repair.
ZLINE
ranges.
An American company, ZLINE Kitchen and Bath, selling professional-style gas, dual-fuel and induction ranges.
ZLINE range repairMore ZLINE codes
Surface elements and induction on other makes
Gas range
Open flames on top and a gas-fired oven below, all fed by one supply line behind the range and lit by igniters rather than a match.
Dual-fuel range
Gas burners on top and an electric oven below, the combination most professional-style ranges use, needing both a gas line and a 240-volt circuit.
Induction range
A glass top that heats the pan itself through copper coils and power boards, over an electric oven, with electronics doing almost all the work.
In ZLINE's own words
E/1 – Coil Temperature
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Induction ranges in ZLINE's MINR and SINR families.
ZLINE E/1 range repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E/1.
Can I clear E/1 myself?
Can a large pan cause E/1 on my ZLINE induction range?
My ZLINE shows E/1 after long boiling at full power. Is that expected?
Back to your everyday
Still showing E/1?
Book with the code exactly as it appears, the full model number, and whether you notice any smell of gas or scorching — with a code, that is where the diagnosis begins.