Bosch induction range
showing F1
On Bosch induction slide-ins, F1 and F6 mean a cooking zone got too hot and shut off to protect the glass.
Mon–Sat, 8am–8pm
- Surface elements and induction
- Surface element and glass top repair
- Source: Bosch
Book a visit
Three short steps, about a minute.
or call (844) 875-7576
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F1
actually means.
On Bosch induction slide-ins, F1 and F6 mean a cooking zone got too hot and shut off to protect the glass. An empty or dry pan on high heat is a common trigger.
Bosch range display · also shown as F6
What to do when F1 shows on the rangeKind of codeSurface elements and induction
A radiant element, a coil or an induction zone did not heat the way the control expected, or ran hotter than it should. The pan, the switch behind the knob and the wiring to the element come first; on induction, the power board and the coil under the glass are checked next. A zone that will not switch off, or a crack in the glass, means the breaker goes off before anything else.
Usually leads toSurface element and glass top repair
Electric zones that stay cold, run too hot or will not switch off, and cracked or damaged glass on radiant and induction models.
Shows up asRange Surface Element Not Heating
One coil or glass-top zone on an electric range stays cold, heats only weakly, or will not respond while the others work.
MakeBosch
A BSH brand known in the US for slide-in ranges in gas, electric, dual-fuel and induction versions.
SourceBosch "Slide-in Range Error Codes" (Induction Slide-In Ranges)
F1 is on Bosch's slide-in range page, in the induction slide-in section.
Before you book,
in this order.
Each step comes from Bosch's own guidance for F1 on its ranges. Follow it to the end: the last card says whether this is a visit.
Let the electronics cool down.
Switch the zone back on and carry on cooking.
Still there?
It usually turns into surface element and glass top repair. Book with the code and the model number.
What not to do
F1 here is not about the oven; it concerns a zone on top.
What you may
notice with it.
The range problems F1 tends to arrive with. Answer these at the range before anyone is booked.
All problems
Range Surface Element Not Heating
6 causes, cheapest first
Where F1 usually leads
Surface element and glass top repair.
Bosch
ranges.
A BSH brand known in the US for slide-in ranges in gas, electric, dual-fuel and induction versions.
Bosch range repairMore Bosch codes
All 14 Bosch codesSurface elements and induction on other makes
Gas range
Open flames on top and a gas-fired oven below, all fed by one supply line behind the range and lit by igniters rather than a match.
Electric range
Coil elements or radiant elements under a smooth glass top, with an electric oven below, all running on a dedicated 240-volt circuit.
Dual-fuel range
Gas burners on top and an electric oven below, the combination most professional-style ranges use, needing both a gas line and a 240-volt circuit.
In Bosch's own words
The cooking zone has overheated. It has switched off to protect the work surface.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. F1 is on Bosch's slide-in range page, in the induction slide-in section.
Bosch F1 range repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F1.
Can I clear F1 myself?
Why did my Bosch zone show F1 while searing?
Is F6 on my Bosch induction range a repair?
Back to your everyday
Still showing F1?
Book with the code exactly as it appears, the full model number, and whether you notice any smell of gas or scorching — with a code, that is where the diagnosis begins.