GE Profile induction range with a flashing power setting
On GE Profile induction ranges, an element whose power setting flashes has usually rejected the pan.
Mon–Sat, 8am–8pm
- Surface elements and induction
- Surface element and glass top repair
- Source: GE Profile
Book a visit
Three short steps, about a minute.
or call (844) 875-7576
Loading appointment form…
The appointment form couldn’t load. Please try again.
What Flashing power setting
actually means.
On GE Profile induction ranges, an element whose power setting flashes has usually rejected the pan. GE lists a pan that is not magnetic, one below the minimum size, one that is off-center, or one that does not sit flat on the glass.
GE Profile range display
What to do when Flashing power setting shows on the rangeKind of codeSurface elements and induction
A radiant element, a coil or an induction zone did not heat the way the control expected, or ran hotter than it should. The pan, the switch behind the knob and the wiring to the element come first; on induction, the power board and the coil under the glass are checked next. A zone that will not switch off, or a crack in the glass, means the breaker goes off before anything else.
Usually leads toSurface element and glass top repair
Electric zones that stay cold, run too hot or will not switch off, and cracked or damaged glass on radiant and induction models.
Shows up asInduction Range Not Detecting Pan
An induction zone flashes, beeps, shows its no-pan symbol or switches itself off, even with a pan sitting right on it.
MakeGE Profile
The step-up line from GE Appliances, with slide-in and freestanding ranges that add convection, air fry and induction.
SourceGE Profile owner's manual, 30-inch induction range PHS930/PHS93E
GE Profile induction ranges PHS930 and PHS93E (manual 49-2000990).
Before you book,
in this order.
Each step comes from GE Profile's own guidance for Flashing power setting on its ranges. Follow it to the end: the last card says whether this is a visit.
Test the pan with a magnet; induction needs a pan it will hold.
Use a flat pan at least the minimum size for that element and center it.
If a suitable pan still gets no heat, book a visit.
Still there?
It usually turns into surface element and glass top repair. Book with the code and the model number.
What not to do
A flashing setting is not proof of a burned-out coil; the pan is checked first.
What you may
notice with it.
The range problems Flashing power setting tends to arrive with. Answer these at the range before anyone is booked.
All problems
Where Flashing power setting usually leads
Surface element and glass top repair.
GE Profile
ranges.
The step-up line from GE Appliances, with slide-in and freestanding ranges that add convection, air fry and induction.
GE Profile range repair
Gas range
Open flames on top and a gas-fired oven below, all fed by one supply line behind the range and lit by igniters rather than a match.
Electric range
Coil elements or radiant elements under a smooth glass top, with an electric oven below, all running on a dedicated 240-volt circuit.
Dual-fuel range
Gas burners on top and an electric oven below, the combination most professional-style ranges use, needing both a gas line and a 240-volt circuit.
In GE Profile's own words
Pan is too small.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. GE Profile induction ranges PHS930 and PHS93E (manual 49-2000990).
GE Profile Flashing power setting range repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about Flashing power setting.
Can I clear Flashing power setting myself?
Why does my GE Profile induction element flash with my old pan?
Can a flashing setting on a GE Profile mean a real failure?
Back to your everyday
Still showing Flashing power setting?
Book with the code exactly as it appears, the full model number, and whether you notice any smell of gas or scorching — with a code, that is where the diagnosis begins.