

Electrolux range
showing F40
On Electrolux ranges covered by the guide, F40 and F41 mean the control has locked the top out, so the surface elements will not turn on.
Mon–Sat, 8am–8pm
- Surface elements and induction
- Surface element and glass top repair
- Source: Electrolux
Book a visit
Three short steps, about a minute.
or call (844) 875-7576
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F40
actually means.
On Electrolux ranges covered by the guide, F40 and F41 mean the control has locked the top out, so the surface elements will not turn on.
Electrolux range display · also shown as F41
What to do when F40 shows on the rangeKind of codeSurface elements and induction
A radiant element, a coil or an induction zone did not heat the way the control expected, or ran hotter than it should. The pan, the switch behind the knob and the wiring to the element come first; on induction, the power board and the coil under the glass are checked next. A zone that will not switch off, or a crack in the glass, means the breaker goes off before anything else.
Usually leads toSurface element and glass top repair
Electric zones that stay cold, run too hot or will not switch off, and cracked or damaged glass on radiant and induction models.
Shows up asRange Surface Element Not Heating
One coil or glass-top zone on an electric range stays cold, heats only weakly, or will not respond while the others work.
MakeElectrolux
A Swedish appliance group whose US ranges are front-control models in gas, electric and induction versions.
SourceElectrolux "Range Error Code F40 / F41 - Cooktop Lock Out"
Older Electrolux electric ranges are the ones that show F40; the ECF models report Err with a number.
Before you book,
in this order.
Each step comes from Electrolux's own guidance for F40 on its ranges. Follow it to the end: the last card says whether this is a visit.
Cut power to the range for about 30 seconds.
Book a visit if the lockout code returns.
Still there?
It usually turns into surface element and glass top repair. Book with the code and the model number.
What not to do
This is not the lock you set yourself, which shows a dash.
What you may
notice with it.
The range problems F40 tends to arrive with. Answer these at the range before anyone is booked.
All problems
Range Surface Element Not Heating
6 causes, cheapest first
Where F40 usually leads
Surface element and glass top repair.
Electrolux
ranges.
A Swedish appliance group whose US ranges are front-control models in gas, electric and induction versions.
Electrolux range repairMore Electrolux codes
Surface elements and induction on other makes
Gas range
Open flames on top and a gas-fired oven below, all fed by one supply line behind the range and lit by igniters rather than a match.
Dual-fuel range
Gas burners on top and an electric oven below, the combination most professional-style ranges use, needing both a gas line and a 240-volt circuit.
Induction range
A glass top that heats the pan itself through copper coils and power boards, over an electric oven, with electronics doing almost all the work.
In Electrolux's own words
Electric Range Error Code F40 / F41 - Cooktop Lock Out
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Older Electrolux electric ranges are the ones that show F40; the ECF models report Err with a number.
Electrolux F40 range repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F40.
Can I clear F40 myself?
Can I still bake on my Electrolux range while F40 is showing?
Why would an Electrolux range lock out its own top?
Back to your everyday
Still showing F40?
Book with the code exactly as it appears, the full model number, and whether you notice any smell of gas or scorching — with a code, that is where the diagnosis begins.