ZLINE induction range
showing F/3
Each induction coil on a ZLINE range has a temperature sensor, called an NTC, and F/3 means that sensor has failed or is not connected properly.
Mon–Sat, 8am–8pm
- Temperature sensor
- Temperature sensor and thermostat repair
- Source: ZLINE
Book a visit
Three short steps, about a minute.
or call (844) 875-7576
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F/3
actually means.
Each induction coil on a ZLINE range has a temperature sensor, called an NTC, and F/3 means that sensor has failed or is not connected properly. Without it the control cannot judge the coil's heat.
ZLINE range display · also shown as F3
What to do when F/3 shows on the rangeKind of codeTemperature sensor
The oven sensor sent a reading the control would not accept, or one that climbed well past the setting. A loose plug or a sensor that has drifted is ruled out before the control board, and a temperature that keeps rising means the range is switched off at the breaker first.
Usually leads toTemperature sensor and thermostat repair
A range oven that bakes hot, bakes slow, takes forever to preheat or posts a sensor code, traced to the sensor probe, the thermostat or the calibration.
Shows up asRange Error Code
The range display shows letters, numbers or a flashing symbol, beeps, and stops the oven, a cooking zone or a clean.
MakeZLINE
An American company, ZLINE Kitchen and Bath, selling professional-style gas, dual-fuel and induction ranges.
SourceZLINE Induction Ranges User Manual
ZLINE MINR and SINR induction ranges; F/3 sits in the F group, which ZLINE reserves for internal parts.
Before you book,
in this order.
Each step comes from ZLINE's own guidance for F/3 on its ranges. Follow it to the end: the last card says whether this is a visit.
Stop using the affected zone.
Book a visit; ZLINE advises owners not to attempt this repair.
Still there?
It usually turns into temperature sensor and thermostat repair. Book with the code and the model number.
What not to do
F/3 is listed separately from E/5, which ZLINE uses for a coil sensor that has been disconnected or moved out of position.
What you may
notice with it.
The range problems F/3 tends to arrive with. Answer these at the range before anyone is booked.
All problems
Range Error Code
6 causes, cheapest first
Where F/3 usually leads
Temperature sensor and thermostat repair.
ZLINE
ranges.
An American company, ZLINE Kitchen and Bath, selling professional-style gas, dual-fuel and induction ranges.
ZLINE range repair
Gas range
Open flames on top and a gas-fired oven below, all fed by one supply line behind the range and lit by igniters rather than a match.
Dual-fuel range
Gas burners on top and an electric oven below, the combination most professional-style ranges use, needing both a gas line and a 240-volt circuit.
Induction range
A glass top that heats the pan itself through copper coils and power boards, over an electric oven, with electronics doing almost all the work.
In ZLINE's own words
F/3 – NTC Sensor Failure
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. ZLINE MINR and SINR induction ranges; F/3 sits in the F group, which ZLINE reserves for internal parts.
ZLINE F/3 range repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F/3.
Can I clear F/3 myself?
Is F/3 on a ZLINE range the sensor or the coil?
Can I reset F/3 on my ZLINE induction range?
Back to your everyday
Still showing F/3?
Book with the code exactly as it appears, the full model number, and whether you notice any smell of gas or scorching — with a code, that is where the diagnosis begins.