BlueStar Platinum induction range
showing E6
E6 on a BlueStar Platinum induction range has two listed causes: the voltage reaching the range is too low, or something inside the induction system is wrong.
Mon–Sat, 8am–8pm
- Surface elements and induction
- Surface element and glass top repair
- Source: BlueStar
Book a visit
Three short steps, about a minute.
or call (844) 875-7576
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E6
actually means.
E6 on a BlueStar Platinum induction range has two listed causes: the voltage reaching the range is too low, or something inside the induction system is wrong.
BlueStar range display
What to do when E6 shows on the rangeKind of codeSurface elements and induction
A radiant element, a coil or an induction zone did not heat the way the control expected, or ran hotter than it should. The pan, the switch behind the knob and the wiring to the element come first; on induction, the power board and the coil under the glass are checked next. A zone that will not switch off, or a crack in the glass, means the breaker goes off before anything else.
Usually leads toSurface element and glass top repair
Electric zones that stay cold, run too hot or will not switch off, and cracked or damaged glass on radiant and induction models.
Shows up asRange Surface Element Not Heating
One coil or glass-top zone on an electric range stays cold, heats only weakly, or will not respond while the others work.
MakeBlueStar
A Pennsylvania company that builds professional-style gas and dual-fuel ranges, known for open burners and a very wide choice of finishes.
SourceBlueStar Platinum induction range manual 100799, induction indicators
BlueStar BSPIR Platinum induction ranges.
Before you book,
in this order.
Each step comes from BlueStar's own guidance for E6 on its ranges. Follow it to the end: the last card says whether this is a visit.
Check the range's breaker and whether other appliances on the same supply work normally.
Do not work on the outlet or wiring yourself; if E6 persists, book a visit so the supply and the range can be tested.
Still there?
It usually turns into surface element and glass top repair. Book with the code and the model number.
What not to do
E6 is not about the pan or its size; it concerns power reaching the induction electronics.
What you may
notice with it.
The range problems E6 tends to arrive with. Answer these at the range before anyone is booked.
All problems
Where E6 usually leads
Surface element and glass top repair.
BlueStar
ranges.
A Pennsylvania company that builds professional-style gas and dual-fuel ranges, known for open burners and a very wide choice of finishes.
BlueStar range repairMore BlueStar codes
Surface elements and induction on other makes
Gas range
Open flames on top and a gas-fired oven below, all fed by one supply line behind the range and lit by igniters rather than a match.
Dual-fuel range
Gas burners on top and an electric oven below, the combination most professional-style ranges use, needing both a gas line and a 240-volt circuit.
Induction range
A glass top that heats the pan itself through copper coils and power boards, over an electric oven, with electronics doing almost all the work.
In BlueStar's own words
Voltage of the electrical power
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. BlueStar BSPIR Platinum induction ranges.
BlueStar E6 range repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E6.
Can I clear E6 myself?
Can low voltage in my house cause E6 on a BlueStar induction range?
My BlueStar shows E6 but the lights in the kitchen are fine. What else could it be?
Back to your everyday
Still showing E6?
Book with the code exactly as it appears, the full model number, and whether you notice any smell of gas or scorching — with a code, that is where the diagnosis begins.