BlueStar range
showing F50
Probe Error F50 tells you the range has a problem with the meat probe.
Mon–Sat, 8am–8pm
- Temperature sensor
- Temperature sensor and thermostat repair
- Source: BlueStar
Book a visit
Three short steps, about a minute.
or call (844) 875-7576
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F50
actually means.
Probe Error F50 tells you the range has a problem with the meat probe. BlueStar separates it from the simpler messages Probe Not Detected, which just asks you to plug the probe in, and Remove Probe, shown when the probe is left in during Broil or Clean.
BlueStar range display · also shown as Probe Error F50
What to do when F50 shows on the rangeKind of codeTemperature sensor
The oven sensor sent a reading the control would not accept, or one that climbed well past the setting. A loose plug or a sensor that has drifted is ruled out before the control board, and a temperature that keeps rising means the range is switched off at the breaker first.
Usually leads toTemperature sensor and thermostat repair
A range oven that bakes hot, bakes slow, takes forever to preheat or posts a sensor code, traced to the sensor probe, the thermostat or the calibration.
Shows up asRange Oven Temperature Wrong
Recipes burn or come out underdone, and an oven thermometer disagrees with the temperature set on the range.
MakeBlueStar
A Pennsylvania company that builds professional-style gas and dual-fuel ranges, known for open burners and a very wide choice of finishes.
SourceBlueStar dual-fuel range manual 200009, troubleshooting
BlueStar BSDF dual-fuel and BSPIR Platinum induction ranges.
Before you book,
in this order.
Each step comes from BlueStar's own guidance for F50 on its ranges. Follow it to the end: the last card says whether this is a visit.
Take the probe out and check that the plug and socket are clean and undamaged.
If Probe Error F50 still shows, book a visit.
Still there?
It usually turns into temperature sensor and thermostat repair. Book with the code and the model number.
What not to do
F50 is not the Remove Probe message. That one only asks you to take the probe out before Broil or Clean.
What you may
notice with it.
The range problems F50 tends to arrive with. Answer these at the range before anyone is booked.
All problems
Range Oven Temperature Wrong
5 causes, cheapest first
Where F50 usually leads
Temperature sensor and thermostat repair.
BlueStar
ranges.
A Pennsylvania company that builds professional-style gas and dual-fuel ranges, known for open burners and a very wide choice of finishes.
BlueStar range repair
Gas range
Open flames on top and a gas-fired oven below, all fed by one supply line behind the range and lit by igniters rather than a match.
Dual-fuel range
Gas burners on top and an electric oven below, the combination most professional-style ranges use, needing both a gas line and a 240-volt circuit.
Induction range
A glass top that heats the pan itself through copper coils and power boards, over an electric oven, with electronics doing almost all the work.
In BlueStar's own words
Probe Error F50
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. BlueStar BSDF dual-fuel and BSPIR Platinum induction ranges.
BlueStar F50 range repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F50.
Can I clear F50 myself?
Can I still use my BlueStar oven with Probe Error F50?
What is the difference between Probe Error F50 and Remove Probe on a BlueStar?
Back to your everyday
Still showing F50?
Book with the code exactly as it appears, the full model number, and whether you notice any smell of gas or scorching — with a code, that is where the diagnosis begins.