AGA eR7 range
showing CE
CE appears when the touch panel sends commands and gets no answer from the main board in the base of the range.
Mon–Sat, 8am–8pm
- Controls and communication
- Knobs, switches and controls
- Source: AGA
Book a visit
Three short steps, about a minute.
or call (844) 875-7576
Loading appointment form…
The appointment form couldn’t load. Please try again.
What CE
actually means.
CE appears when the touch panel sends commands and gets no answer from the main board in the base of the range. The two are joined by a communication cable routed inside the cooker, so the link between them is the first suspect.
AGA range display
What to do when CE shows on the rangeKind of codeControls and communication
The display, the main board or the induction power board lost contact with one another, or one of them failed its own self-check. A power dip, a loose cable or moisture from a boil-over is ruled out before a board is replaced, and a range that keeps heating while this code shows is switched off at the breaker.
Usually leads toKnobs, switches and controls
Knobs that spin or crack, touch keys that do nothing, blank displays, clocks that reset and control boards that switch the wrong thing.
Shows up asRange Error Code
The range display shows letters, numbers or a flashing symbol, beeps, and stops the oven, a cooking zone or a clean.
MakeAGA
A British cooking name, owned by Middleby, that sells cast-iron heat-storage cookers and more conventional dual-fuel and induction ranges in the US.
SourceAGA eR7 Field Service Manual, USA and Canada
eR7 cast-iron ranges; the communication cable runs inside the cooker from the base board to the panel behind the top left door.
Before you book,
in this order.
Each step comes from AGA's own guidance for CE on its ranges. Follow it to the end: the last card says whether this is a visit.
Note CE and whether anything was moved or worked on recently.
Book a visit; the technician checks the communication cable and both of its sockets before looking at either board.
Still there?
It usually turns into knobs, switches and controls. Book with the code and the model number.
What not to do
CE is different from the handset losing contact. The handset shows its own no-link symbol when the range is off, in standby or out of range.
What you may
notice with it.
The range problems CE tends to arrive with. Answer these at the range before anyone is booked.
All problems
Range Error Code
6 causes, cheapest first
Where CE usually leads
Knobs, switches and controls.
AGA
ranges.
A British cooking name, owned by Middleby, that sells cast-iron heat-storage cookers and more conventional dual-fuel and induction ranges in the US.
AGA range repairMore AGA codes
All 21 AGA codesControls and communication on other makes
Electric range
Coil elements or radiant elements under a smooth glass top, with an electric oven below, all running on a dedicated 240-volt circuit.
Dual-fuel range
Gas burners on top and an electric oven below, the combination most professional-style ranges use, needing both a gas line and a 240-volt circuit.
Induction range
A glass top that heats the pan itself through copper coils and power boards, over an electric oven, with electronics doing almost all the work.
In AGA's own words
Error code CE: No response from main controller.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. eR7 cast-iron ranges; the communication cable runs inside the cooker from the base board to the panel behind the top left door.
AGA CE range repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about CE.
Can I clear CE myself?
Is CE on my AGA eR7 usually a failed board?
My AGA eR7 handset lost its link. Is that the same as CE?
Back to your everyday
Still showing CE?
Book with the code exactly as it appears, the full model number, and whether you notice any smell of gas or scorching — with a code, that is where the diagnosis begins.