Wolf legacy dual-fuel range
showing PF
PF in the oven knob window most often means the power went out while the range was on.
Mon–Sat, 8am–8pm
- Mode, not a failure
- No repair needed
- Source: Wolf
Book a visit
Three short steps, about a minute.
or call (844) 875-7576
Loading appointment form…
The appointment form couldn’t load. Please try again.
What PF
actually means.
PF in the oven knob window most often means the power went out while the range was on. Wolf also shows it when the oven is still too hot for the cooking mode you just selected.
Wolf range display · also shown as P F
What to do when PF shows on the rangeKind of codeMode, not a failure
Something the range was told to do, or a state it chose on purpose — a control lock, a Sabbath setting, a demo mode that lights the display but never heats, a pan warning on an induction zone. Nothing has worn out, and no part is needed.
Usually leads toNo repair
Turn the oven selector bezel to any cooking mode and then back to OFF to clear PF.
Shows up asRange Control Panel Not Responding
The touch keys or knobs on the range do nothing, only some keys work, the display is blank or frozen, or it beeps without starting.
MakeWolf
The cooking brand of the Wisconsin-based Sub-Zero Group, known for red-knobbed gas, dual-fuel and induction ranges.
SourceWolf answer: legacy dual-fuel range, PF
Legacy Wolf dual-fuel ranges.
Before you book,
in this order.
Each step comes from Wolf's own guidance for PF on its ranges. Follow it to the end: the last card says whether this is a visit.
Turn the oven selector bezel to any cooking mode and then back to OFF to clear PF.
If the oven is hot, open the door to let it cool before choosing the mode again.
Cleared?
The range was set right without a new part. If the same message comes back while a burner or the oven is in use, or the range cuts out again, treat it as a new problem and book it.
What not to do
PF by itself is not a broken part. Book a visit only if it keeps returning after the reset, the cooling and a breaker cycle.
What you may
notice with it.
The range problems PF tends to arrive with. Answer these at the range before anyone is booked.
All problems
Range Control Panel Not Responding
5 causes, cheapest first
No repair indicated
Nothing to repair.
Something the range was told to do, or a state it chose on purpose — a control lock, a Sabbath setting, a demo mode that lights the display but never heats, a pan warning on an induction zone. Nothing has worn out, and no part is needed.
Wolf
ranges.
The cooking brand of the Wisconsin-based Sub-Zero Group, known for red-knobbed gas, dual-fuel and induction ranges.
Wolf range repairMore Wolf codes
Mode, not a failure on other makes
Gas range
Open flames on top and a gas-fired oven below, all fed by one supply line behind the range and lit by igniters rather than a match.
Dual-fuel range
Gas burners on top and an electric oven below, the combination most professional-style ranges use, needing both a gas line and a 240-volt circuit.
Induction range
A glass top that heats the pan itself through copper coils and power boards, over an electric oven, with electronics doing almost all the work.
In Wolf's own words
Unit had a power failure
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Legacy Wolf dual-fuel ranges.
Wolf PF range repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about PF.
Can I clear PF myself?
Why does my Wolf range show PF after a storm?
My Wolf shows PF right after broiling. Is that normal?
Back to your everyday
Still showing PF?
Book with the code exactly as it appears, the full model number, and whether you notice any smell of gas or scorching — with a code, that is where the diagnosis begins.