Thermador induction range
showing F2
Thermador uses F2, or E7015, when the electronics overheat and the zone in use turns off.
Mon–Sat, 8am–8pm
- Surface elements and induction
- Surface element and glass top repair
- Source: Thermador
Book a visit
Three short steps, about a minute.
or call (844) 875-7576
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F2
actually means.
Thermador uses F2, or E7015, when the electronics overheat and the zone in use turns off. The other zones may keep working.
Thermador range display · also shown as E7015
What to do when F2 shows on the rangeKind of codeSurface elements and induction
A radiant element, a coil or an induction zone did not heat the way the control expected, or ran hotter than it should. The pan, the switch behind the knob and the wiring to the element come first; on induction, the power board and the coil under the glass are checked next. A zone that will not switch off, or a crack in the glass, means the breaker goes off before anything else.
Usually leads toSurface element and glass top repair
Electric zones that stay cold, run too hot or will not switch off, and cracked or damaged glass on radiant and induction models.
Shows up asRange Surface Element Not Heating
One coil or glass-top zone on an electric range stays cold, heats only weakly, or will not respond while the others work.
MakeThermador
A luxury BSH brand selling Pro Harmony and Pro Grand ranges in gas, dual-fuel and induction versions.
SourceThermador "Ranges - Error Codes" support page
Only Thermador's induction models show F2; the gas and dual-fuel ranges do not have an induction top.
Before you book,
in this order.
Each step comes from Thermador's own guidance for F2 on its ranges. Follow it to the end: the last card says whether this is a visit.
Let the electronics cool.
Touch any control and continue once the message is gone.
Still there?
It usually turns into surface element and glass top repair. Book with the code and the model number.
What not to do
F2 affects one zone; F4 means all zones turned off.
What you may
notice with it.
The range problems F2 tends to arrive with. Answer these at the range before anyone is booked.
All problems
Range Surface Element Not Heating
6 causes, cheapest first
Where F2 usually leads
Surface element and glass top repair.
Thermador
ranges.
A luxury BSH brand selling Pro Harmony and Pro Grand ranges in gas, dual-fuel and induction versions.
Thermador range repairMore Thermador codes
Surface elements and induction on other makes
Gas range
Open flames on top and a gas-fired oven below, all fed by one supply line behind the range and lit by igniters rather than a match.
Dual-fuel range
Gas burners on top and an electric oven below, the combination most professional-style ranges use, needing both a gas line and a 240-volt circuit.
Induction range
A glass top that heats the pan itself through copper coils and power boards, over an electric oven, with electronics doing almost all the work.
In Thermador's own words
The electronics have overheated. The corresponding cooking zone has been switched off.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Only Thermador's induction models show F2; the gas and dual-fuel ranges do not have an induction top.
Thermador F2 range repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F2.
Can I clear F2 myself?
Only one zone on my Thermador stopped with F2. Why?
F2 keeps coming back on my Thermador. Is that still normal?
Back to your everyday
Still showing F2?
Book with the code exactly as it appears, the full model number, and whether you notice any smell of gas or scorching — with a code, that is where the diagnosis begins.