Miele range not recognizing its wireless probe
Miele shows this message when the wireless probe is not recognized.
Mon–Sat, 8am–8pm
- Temperature sensor
- Temperature sensor and thermostat repair
- Source: Miele
Book a visit
Three short steps, about a minute.
or call (844) 875-7576
Loading appointment form…
The appointment form couldn’t load. Please try again.
What No signal to the probe
actually means.
Miele shows this message when the wireless probe is not recognized. A microwave running nearby can interfere, because it uses a similar frequency range.
Miele range display
What to do when No signal to the probe shows on the rangeKind of codeTemperature sensor
The oven sensor sent a reading the control would not accept, or one that climbed well past the setting. A loose plug or a sensor that has drifted is ruled out before the control board, and a temperature that keeps rising means the range is switched off at the breaker first.
Usually leads toTemperature sensor and thermostat repair
A range oven that bakes hot, bakes slow, takes forever to preheat or posts a sensor code, traced to the sensor probe, the thermostat or the calibration.
Shows up asRange Oven Temperature Wrong
Recipes burn or come out underdone, and an oven thermometer disagrees with the temperature set on the range.
MakeMiele
A family-owned German company selling professional-style dual-fuel and all-gas ranges in the US.
SourceMiele operating instructions, 30 inch dual fuel range (HR 1924-3 G DF product page), Frequently asked questions
In the 30-inch dual fuel range manual; applies to models with the wireless probe.
Before you book,
in this order.
Each step comes from Miele's own guidance for No signal to the probe on its ranges. Follow it to the end: the last card says whether this is a visit.
Reposition the probe in the food.
Turn off any microwave running near the oven.
If it is still not recognized, the probe may need replacing.
Still there?
It usually turns into temperature sensor and thermostat repair. Book with the code and the model number.
What not to do
This is not an oven temperature sensor code.
What you may
notice with it.
The range problems No signal to the probe tends to arrive with. Answer these at the range before anyone is booked.
All problems
Range Oven Temperature Wrong
5 causes, cheapest first
Where No signal to the probe usually leads
Temperature sensor and thermostat repair.
Miele
ranges.
A family-owned German company selling professional-style dual-fuel and all-gas ranges in the US.
Miele range repair
Gas range
Open flames on top and a gas-fired oven below, all fed by one supply line behind the range and lit by igniters rather than a match.
Dual-fuel range
Gas burners on top and an electric oven below, the combination most professional-style ranges use, needing both a gas line and a 240-volt circuit.
Induction range
A glass top that heats the pan itself through copper coils and power boards, over an electric oven, with electronics doing almost all the work.
In Miele's own words
In some cases, reception interference can even be caused by a microwave operating in the vicinity of the oven, because the microwave uses a similar frequency range to that of the wireless probe.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. In the 30-inch dual fuel range manual; applies to models with the wireless probe.
Miele No signal to the probe range repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about No signal to the probe.
Can I clear No signal to the probe myself?
Why does my Miele lose the probe only when the microwave is on?
Is a new probe the fix when my Miele never finds it?
Back to your everyday
Still showing No signal to the probe?
Book with the code exactly as it appears, the full model number, and whether you notice any smell of gas or scorching — with a code, that is where the diagnosis begins.