---
title: "Range Error Codes — What They Mean | RangeRepair.center"
description: "What a range error code can tell you and where it stops, which codes are only a lock or a setting, and how to read one against your own model before booking."
url: "https://rangerepair.center/error-codes/"
---

Error codes

# Range error codes, read properly.

A code narrows the search and is also the thing most often read wrong: the same characters mean different things on different brands, and a fair number of the codes people look up are not failures at all — they are modes the appliance was left in.

## Find your code, make by make.

Type the characters exactly as the display shows them, or pick the make. Each code has a page of its own: what it means on that brand, what to check, and what not to do.

### AGA range error codes 21 codes

- [FE Controls and communication The touch panel's own processor has stopped responding.](https://rangerepair.center/error-codes/aga-fe/)
- [VE Controls and communication The main board's firmware does not match the touch panel.](https://rangerepair.center/error-codes/aga-ve/)
- [CE Controls and communication The touch panel cannot hear the main board.](https://rangerepair.center/error-codes/aga-ce/)
- [S Mode, not a failure Slumber: the roasting and baking ovens are idling on low heat.](https://rangerepair.center/error-codes/aga-s/)
- [007 Temperature sensor The panel cannot read its thermocouples.](https://rangerepair.center/error-codes/aga-007/)
- [010-014 Oven heating A zone took too long to reach its heat at full power.](https://rangerepair.center/error-codes/aga-010-014/)
- [020-024 Temperature sensor The two halves of a zone's thermocouple disagree.](https://rangerepair.center/error-codes/aga-020-024/)
- [060-100 Temperature sensor A thermocouple circuit reads as broken.](https://rangerepair.center/error-codes/aga-060-100/)
- [110-116 Controls and communication A relay on the main board has shorted.](https://rangerepair.center/error-codes/aga-110-116/)
- [120-124 Temperature sensor A zone reads as overheated, often from swapped probe plugs.](https://rangerepair.center/error-codes/aga-120-124/)
- [130-136 Oven heating The electronic switch feeding an element reports a problem.](https://rangerepair.center/error-codes/aga-130-136/)
- [139 Door and lock The control panel behind the top left door is running too hot.](https://rangerepair.center/error-codes/aga-139/)
- [140 Controls and communication The board's configuration key is missing or wrong for the supply.](https://rangerepair.center/error-codes/aga-140/)
- [150-156 Controls and communication A relay on the main board will not close.](https://rangerepair.center/error-codes/aga-150-156/)
- [159 Controls and communication The wireless receiver is not talking to the main board.](https://rangerepair.center/error-codes/aga-159/)
- [E2 Surface elements and induction The induction electronics are too hot.](https://rangerepair.center/error-codes/aga-e2/)
- [U400 Controls and communication The range is connected to the supply incorrectly.](https://rangerepair.center/error-codes/aga-u400/)
- [Er Surface elements and induction An internal problem the owner cannot fix.](https://rangerepair.center/error-codes/aga-er/)
- [E6 Surface elements and induction Linked to poor-quality or unsuitable induction pans.](https://rangerepair.center/error-codes/aga-e6/)
- [H Mode, not a failure Residual heat: the zone is still above 140°F.](https://rangerepair.center/error-codes/aga-h/)
- [L Mode, not a failure The child lock is on for the induction top.](https://rangerepair.center/error-codes/aga-l/)

[AGA range repair](https://rangerepair.center/brands/aga/)

### Samsung range error codes 15 codes

- [C-20 Temperature sensor The sensor that measures oven heat reads open or shorted.](https://rangerepair.center/error-codes/samsung-c-20/)
- [C-21 Oven heating The oven is getting hotter than the control allows.](https://rangerepair.center/error-codes/samsung-c-21/)
- [C-24 Oven heating Oven heat is rising too fast, usually because the vent is covered.](https://rangerepair.center/error-codes/samsung-c-24/)
- [C-25 Oven heating The gas oven did not warm up the way it should.](https://rangerepair.center/error-codes/samsung-c-25/)
- [C-30 Temperature sensor A temperature sensor on the main control board reads wrong, or the board is too hot.](https://rangerepair.center/error-codes/samsung-c-30/)
- [C-d0 Controls and communication A control key reads as stuck.](https://rangerepair.center/error-codes/samsung-c-d0/)
- [C-d1 Door and lock The oven door lock is out of position.](https://rangerepair.center/error-codes/samsung-c-d1/)
- [C-F0 Controls and communication Two electronic boards in the range have stopped talking to each other.](https://rangerepair.center/error-codes/samsung-c-f0/)
- [bAd LinE Controls and communication The power cord is not connected correctly.](https://rangerepair.center/error-codes/samsung-bad-line/)
- [tESt Mode, not a failure The range is in Demo mode, so nothing heats.](https://rangerepair.center/error-codes/samsung-test/)
- [-dC- Mode, not a failure The oven divider is missing or not seated.](https://rangerepair.center/error-codes/samsung-dc/)
- [door Door and lock The control thinks the oven door is open.](https://rangerepair.center/error-codes/samsung-door/)
- [Cooktop in use Mode, not a failure Self Clean will not start while a burner or element is on.](https://rangerepair.center/error-codes/samsung-top-in-use/)
- [Underlined u Surface elements and induction The induction zone does not detect a suitable pan.](https://rangerepair.center/error-codes/samsung-underlined-u/)
- [C-10 Mode, not a failure A self-diagnosis in SmartThings saw an odd starting temperature.](https://rangerepair.center/error-codes/samsung-c-10/)

[Samsung range repair](https://rangerepair.center/brands/samsung/)

### Bosch range error codes 14 codes

- [e005 Controls and communication The display and the power board are not communicating.](https://rangerepair.center/error-codes/bosch-e005/)
- [e011 Controls and communication A touch sensor on the oven control panel failed.](https://rangerepair.center/error-codes/bosch-e011/)
- [e101 Temperature sensor The appliance temperature sensor is not working correctly.](https://rangerepair.center/error-codes/bosch-e101/)
- [e126 Door and lock The door lock is not working properly.](https://rangerepair.center/error-codes/bosch-e126/)
- [E302 Controls and communication The control panel or the power board has overheated.](https://rangerepair.center/error-codes/bosch-e302/)
- [e310 Controls and communication The power supply to the range has failed.](https://rangerepair.center/error-codes/bosch-e310/)
- [ERR/toP Mode, not a failure A zone on top was turned on during Self Clean.](https://rangerepair.center/error-codes/bosch-err-top/)
- [dE Mode, not a failure Demo mode is on, so the zones will not heat.](https://rangerepair.center/error-codes/bosch-de/)
- [E9000 Controls and communication The supply voltage is outside the normal range.](https://rangerepair.center/error-codes/bosch-e9000/)
- [E9011 Controls and communication The range is not connected properly.](https://rangerepair.center/error-codes/bosch-e9011/)
- [F1 Surface elements and induction An induction zone overheated and switched off.](https://rangerepair.center/error-codes/bosch-f1/)
- [F2 Surface elements and induction The induction electronics overheated.](https://rangerepair.center/error-codes/bosch-f2/)
- [F5 Surface elements and induction Hot cookware is too close to the controls.](https://rangerepair.center/error-codes/bosch-f5/)
- [F8 Mode, not a failure A zone switched off after running too long untouched.](https://rangerepair.center/error-codes/bosch-f8/)

[Bosch range repair](https://rangerepair.center/brands/bosch/)

### LG range error codes 14 codes

- [F1 Temperature sensor The upper oven temperature sensor has a problem.](https://rangerepair.center/error-codes/lg-f1/)
- [F4 Temperature sensor The lower oven temperature sensor has a problem.](https://rangerepair.center/error-codes/lg-f4/)
- [F9 Oven heating The oven is not heating as it should.](https://rangerepair.center/error-codes/lg-f9/)
- [F10 Door and lock The oven door lock did not work as expected.](https://rangerepair.center/error-codes/lg-f10/)
- [F3 Controls and communication A touch pad key is reading wrong.](https://rangerepair.center/error-codes/lg-f3/)
- [F11 Controls and communication The range's electronic boards lost contact with each other.](https://rangerepair.center/error-codes/lg-f11/)
- [F17 Fans The convection fan is not running as expected.](https://rangerepair.center/error-codes/lg-f17/)
- [F27 Fans The cooling fan stalled or locked while self-cleaning.](https://rangerepair.center/error-codes/lg-f27/)
- [F33 Surface elements and induction A temperature sensor under a front induction zone reads wrong.](https://rangerepair.center/error-codes/lg-f33/)
- [F42 Controls and communication The range sees a voltage problem.](https://rangerepair.center/error-codes/lg-f42/)
- [F51 Surface elements and induction The griddle zone's sensor or heating is not working.](https://rangerepair.center/error-codes/lg-f51/)
- [HS Mode, not a failure The range top is still hot.](https://rangerepair.center/error-codes/lg-hs/)
- [PF Mode, not a failure Power was interrupted.](https://rangerepair.center/error-codes/lg-pf/)
- [Sb Mode, not a failure The range is in Sabbath mode.](https://rangerepair.center/error-codes/lg-sb/)

[LG range repair](https://rangerepair.center/brands/lg/)

### Hestan range error codes 12 codes

- [ERR04 Controls and communication A minor electronic problem has switched off one oven feature.](https://rangerepair.center/error-codes/hestan-range-err04/)
- [ERR20 Controls and communication A non-critical electronic problem; the range can still be used.](https://rangerepair.center/error-codes/hestan-range-err20/)
- [ER01 Burners and ignition The Smart Burner saw no rise in pan temperature.](https://rangerepair.center/error-codes/hestan-smart-burner-er01/)
- [ER03 Mode, not a failure The battery in the Cue pan is low.](https://rangerepair.center/error-codes/hestan-smart-burner-er03/)
- [ER05 Burners and ignition The Smart Burner failed to light after several tries.](https://rangerepair.center/error-codes/hestan-smart-burner-er05/)
- [ER06 Burners and ignition A Smart Burner problem not covered by any other code.](https://rangerepair.center/error-codes/hestan-smart-burner-er06/)
- [Er 03 Controls and communication Water or a utensil is sitting on the touch controls.](https://rangerepair.center/error-codes/hestan-induction-er03/)
- [Er 47 Controls and communication The touch control and the induction boards have lost their link.](https://rangerepair.center/error-codes/hestan-induction-er47/)
- [E2 Surface elements and induction The induction coils have overheated.](https://rangerepair.center/error-codes/hestan-induction-e2/)
- [E6 Surface elements and induction A power board or its supply element is reporting a problem.](https://rangerepair.center/error-codes/hestan-induction-e6/)
- [E8 Fans A cooling fan under the induction top is running at the wrong speed.](https://rangerepair.center/error-codes/hestan-induction-e8/)
- [U 400 Surface elements and induction The supply voltage reaching the range is too high.](https://rangerepair.center/error-codes/hestan-induction-u400/)

[Hestan range repair](https://rangerepair.center/brands/hestan/)

### Wolf range error codes 12 codes

- [01 Door and lock The door lock motor ran, but the lock and unlock switches never reported back.](https://rangerepair.center/error-codes/wolf-df-01/)
- [02 Oven heating The oven got hotter than its safety limit allows.](https://rangerepair.center/error-codes/wolf-df-02/)
- [03 Temperature sensor The oven's RTD sensor reads as an open circuit.](https://rangerepair.center/error-codes/wolf-df-03/)
- [0E Oven heating A power relay reads closed when it should be open.](https://rangerepair.center/error-codes/wolf-df-0e/)
- [COOL FAN Fans The switch that proves the cooling fan is running says it is not.](https://rangerepair.center/error-codes/wolf-df-cool-fan/)
- [COMM ERR Controls and communication The display lost contact with the oven controller.](https://rangerepair.center/error-codes/wolf-df-comm-err/)
- [ERR OC Controls and communication The oven selector knob lost its connection to the oven controller.](https://rangerepair.center/error-codes/wolf-df-err-oc/)
- [PF Mode, not a failure The range lost power, or the oven is too hot for the mode chosen.](https://rangerepair.center/error-codes/wolf-df-pf/)
- [03 Controls and communication Something is pressing the touch controls on the glass continuously.](https://rangerepair.center/error-codes/wolf-ir-03/)
- [E2 Surface elements and induction An induction coil under the glass has run too hot.](https://rangerepair.center/error-codes/wolf-ir-e2/)
- [E8 Fans The fan that cools the induction electronics is not working as expected.](https://rangerepair.center/error-codes/wolf-ir-e8/)
- [47 Controls and communication The internal LIN link between induction boards dropped.](https://rangerepair.center/error-codes/wolf-ir-47/)

[Wolf range repair](https://rangerepair.center/brands/wolf/)

### JennAir range error codes 11 codes

- [F3-1 Temperature sensor The oven sensor, the control or the wiring between them is suspect.](https://rangerepair.center/error-codes/jennair-range-f3-1/)
- [F5 Door and lock The door latch or its switches are not reporting correctly.](https://rangerepair.center/error-codes/jennair-range-f5/)
- [F6 Controls and communication The oven control or its wiring is suspect.](https://rangerepair.center/error-codes/jennair-range-f6/)
- [F7 E0 Door and lock The door latch assembly or its wiring is suspect.](https://rangerepair.center/error-codes/jennair-range-f7-e0/)
- [F8 Temperature sensor The meat probe connection needs checking.](https://rangerepair.center/error-codes/jennair-range-f8/)
- [C81 Surface elements and induction The range top overheated and shut itself off.](https://rangerepair.center/error-codes/jennair-range-c81/)
- [ES Mode, not a failure Energy Save mode has put the display to sleep.](https://rangerepair.center/error-codes/jennair-range-es/)
- [F5E0 Door and lock On the knob-lit professional-style range, a door problem often traced to how the door was refitted.](https://rangerepair.center/error-codes/jennair-pro-f5e0/)
- [F9E0 Controls and communication The range's power supply or outlet wiring is suspect.](https://rangerepair.center/error-codes/jennair-pro-f9e0/)
- [F0E0 Mode, not a failure The system check found nothing wrong.](https://rangerepair.center/error-codes/jennair-pro-f0e0/)
- [Blinking amber lights Controls and communication The knob lights turn amber and blink to say a code is stored.](https://rangerepair.center/error-codes/jennair-pro-amber-lights/)

[JennAir range repair](https://rangerepair.center/brands/jennair/)

### Thermador range error codes 11 codes

- [E Controls and communication The oven control detected a problem and is beeping.](https://rangerepair.center/error-codes/thermador-e-number/)
- [E0211 Controls and communication A Home Connect software update did not finish.](https://rangerepair.center/error-codes/thermador-e0211/)
- [dE Mode, not a failure Demo mode has been switched on.](https://rangerepair.center/error-codes/thermador-de/)
- [E7010 Controls and communication The range cannot connect to Wi-Fi or to the hood.](https://rangerepair.center/error-codes/thermador-e7010/)
- [E9000 Controls and communication The supply voltage is wrong.](https://rangerepair.center/error-codes/thermador-e9000/)
- [U400 Controls and communication The range reports an incorrect supply voltage.](https://rangerepair.center/error-codes/thermador-u400/)
- [F1 Surface elements and induction A cooking zone overheated and turned off.](https://rangerepair.center/error-codes/thermador-f1/)
- [F2 Surface elements and induction The electronics overheated and one zone switched off.](https://rangerepair.center/error-codes/thermador-f2/)
- [F4 Surface elements and induction The electronics overheated and every zone switched off.](https://rangerepair.center/error-codes/thermador-f4/)
- [F5 Surface elements and induction Hot cookware is sitting near the controls.](https://rangerepair.center/error-codes/thermador-f5/)
- [F8 Mode, not a failure The automatic time limit turned a zone off.](https://rangerepair.center/error-codes/thermador-f8/)

[Thermador range repair](https://rangerepair.center/brands/thermador/)

### Dacor range error codes 10 codes

- [C-d0 Controls and communication A control key has read as pressed for a full minute.](https://rangerepair.center/error-codes/dacor-range-c-d0/)
- [C-d1 Door and lock The oven door lock is not where the control expects it.](https://rangerepair.center/error-codes/dacor-range-c-d1/)
- [C-F0 Controls and communication The main and sub control boards stopped talking.](https://rangerepair.center/error-codes/dacor-range-c-f0/)
- [C-F2 Controls and communication The main board lost contact with the touch panel.](https://rangerepair.center/error-codes/dacor-range-c-f2/)
- [C-20 Temperature sensor The oven temperature sensor reads open or shorted.](https://rangerepair.center/error-codes/dacor-range-c-20/)
- [C-21 Oven heating The temperature inside the oven rose abnormally high.](https://rangerepair.center/error-codes/dacor-range-c-21/)
- [C-23 Temperature sensor The plug-in temperature probe reads as shorted.](https://rangerepair.center/error-codes/dacor-range-c-23/)
- [C-24 Oven heating An oven vent or air passage is blocked.](https://rangerepair.center/error-codes/dacor-range-c-24/)
- [C-A2 Fans The cooling motor is not running normally.](https://rangerepair.center/error-codes/dacor-range-c-a2/)
- [C-70 Temperature sensor The steam sensor reads open or shorted.](https://rangerepair.center/error-codes/dacor-range-c-70/)

[Dacor range repair](https://rangerepair.center/brands/dacor/)

### BlueStar range error codes 9 codes

- [F20 Controls and communication The touchscreen reports a problem with the control board or its wiring.](https://rangerepair.center/error-codes/bluestar-range-f20/)
- [F40 Temperature sensor The oven temperature sensor is reporting a problem.](https://rangerepair.center/error-codes/bluestar-range-f40/)
- [F50 Temperature sensor The meat probe or its socket is reporting a problem.](https://rangerepair.center/error-codes/bluestar-range-f50/)
- [F60 Fans The cooling fan behind the control panel has a problem.](https://rangerepair.center/error-codes/bluestar-range-f60/)
- [F80 Oven heating The oven has seen a high-temperature condition.](https://rangerepair.center/error-codes/bluestar-range-f80/)
- [E2 Surface elements and induction The induction system on top has overheated.](https://rangerepair.center/error-codes/bluestar-induction-e2/)
- [E6 Surface elements and induction The supply voltage is too low, or the induction system has a problem.](https://rangerepair.center/error-codes/bluestar-induction-e6/)
- [E8 Fans The cooling fan under the induction top has a problem.](https://rangerepair.center/error-codes/bluestar-induction-e8/)
- [Er47 Controls and communication The induction system reports an internal problem.](https://rangerepair.center/error-codes/bluestar-induction-er47/)

[BlueStar range repair](https://rangerepair.center/brands/bluestar/)

### Frigidaire range error codes 9 codes

- [F10 Oven heating The oven is running hotter than normal.](https://rangerepair.center/error-codes/frigidaire-f10/)
- [F30 Temperature sensor The control reads an open probe circuit.](https://rangerepair.center/error-codes/frigidaire-f30/)
- [F31 Temperature sensor The control reads a shorted probe circuit.](https://rangerepair.center/error-codes/frigidaire-f31/)
- [F1 Controls and communication A key on the control pad reads as shorted.](https://rangerepair.center/error-codes/frigidaire-f1/)
- [F12 Controls and communication The electronic control failed a check on itself.](https://rangerepair.center/error-codes/frigidaire-f12/)
- [F3 Controls and communication The range's boards stopped communicating.](https://rangerepair.center/error-codes/frigidaire-f3/)
- [F40 Surface elements and induction The range top has been locked out.](https://rangerepair.center/error-codes/frigidaire-f40/)
- [F90 Door and lock The oven door lock is not working as expected.](https://rangerepair.center/error-codes/frigidaire-f90/)
- [– Mode, not a failure The range top lock is on.](https://rangerepair.center/error-codes/frigidaire-dash/)

[Frigidaire range repair](https://rangerepair.center/brands/frigidaire/)

### Electrolux range error codes 8 codes

- [Err Controls and communication The range detected a problem and recorded a numbered code.](https://rangerepair.center/error-codes/electrolux-err-number/)
- [5d Mode, not a failure Demo mode is on, so the range will not heat.](https://rangerepair.center/error-codes/electrolux-5d/)
- [F10 Oven heating The oven sensed heat above its normal range.](https://rangerepair.center/error-codes/electrolux-f10/)
- [F30 Temperature sensor The probe circuit reads open or shorted.](https://rangerepair.center/error-codes/electrolux-f30/)
- [F90 Door and lock The door lock reported a problem.](https://rangerepair.center/error-codes/electrolux-f90/)
- [F3 Controls and communication Signals between control parts were lost.](https://rangerepair.center/error-codes/electrolux-f3/)
- [F1 Controls and communication A key on the touch pad is shorted.](https://rangerepair.center/error-codes/electrolux-f1/)
- [F40 Surface elements and induction The control locked out the range top.](https://rangerepair.center/error-codes/electrolux-f40/)

[Electrolux range repair](https://rangerepair.center/brands/electrolux/)

### ILVE range error codes 8 codes

- [E9 Temperature sensor A temperature sensor on an induction coil is damaged.](https://rangerepair.center/error-codes/ilve-e9/)
- [E47 Controls and communication The zone display or the power card is damaged.](https://rangerepair.center/error-codes/ilve-e47/)
- [E5 Surface elements and induction The induction power card is defective.](https://rangerepair.center/error-codes/ilve-e5-e6/)
- [E Surface elements and induction An external error reported by the zone display.](https://rangerepair.center/error-codes/ilve-e/)
- [F Surface elements and induction The induction top has detected a problem in itself.](https://rangerepair.center/error-codes/ilve-f/)
- [U Surface elements and induction No suitable pan, or the 149°F warming setting.](https://rangerepair.center/error-codes/ilve-u/)
- [H Mode, not a failure The zone is off but still hot.](https://rangerepair.center/error-codes/ilve-h/)
- [LLLL Mode, not a failure The key-lock is on and every zone is off.](https://rangerepair.center/error-codes/ilve-llll/)

[ILVE range repair](https://rangerepair.center/brands/ilve/)

### Miele range error codes 8 codes

- [F32 Door and lock The Self Clean door lock did not lock.](https://rangerepair.center/error-codes/miele-f32/)
- [F33 Door and lock The Self Clean door lock did not open.](https://rangerepair.center/error-codes/miele-f33/)
- [Demo Mode Mode, not a failure The showroom program is on, so the oven does not heat.](https://rangerepair.center/error-codes/miele-demo-mode/)
- [Fault Controls and communication A code appeared that the manual does not cover.](https://rangerepair.center/error-codes/miele-unlisted-code/)
- [Maximum operating duration reached Mode, not a failure The oven ran so long that the safety shut-off stopped it.](https://rangerepair.center/error-codes/miele-maximum-operating-duration/)
- [Power failure - Program cancelled Mode, not a failure A short outage stopped the cooking program.](https://rangerepair.center/error-codes/miele-power-failure/)
- [System Lock Mode, not a failure The oven controls are locked.](https://rangerepair.center/error-codes/miele-system-lock/)
- [No signal to the probe Temperature sensor The oven cannot hear the wireless food probe.](https://rangerepair.center/error-codes/miele-probe-no-signal/)

[Miele range repair](https://rangerepair.center/brands/miele/)

### SKS range error codes 8 codes

- [F1~F25 Controls and communication An electronic control error in the oven section.](https://rangerepair.center/error-codes/sks-f1-f25/)
- [F1~F15 Surface elements and induction An electronic error in the induction control, shown on the knob.](https://rangerepair.center/error-codes/sks-induction-knob-f1-f15/)
- [F33~F45 Surface elements and induction An electronic error in the induction section of a dual-fuel range.](https://rangerepair.center/error-codes/sks-f33-f45/)
- [F51~F59 Controls and communication An electronic error in the griddle control.](https://rangerepair.center/error-codes/sks-f51-f59/)
- [F62 Controls and communication An electronic error in the sous vide control.](https://rangerepair.center/error-codes/sks-f62/)
- [F-3 Controls and communication A key on the control panel reads as shorted.](https://rangerepair.center/error-codes/sks-f-3/)
- [F-9 Oven heating The oven is not heating.](https://rangerepair.center/error-codes/sks-f-9/)
- [Loc Mode, not a failure Lock Out is on: the door and most controls are locked.](https://rangerepair.center/error-codes/sks-loc/)

[SKS range repair](https://rangerepair.center/brands/sks/)

### ZLINE range error codes 8 codes

- [F/1 Controls and communication The main power board is not working or the boards have lost contact.](https://rangerepair.center/error-codes/zline-f1/)
- [F/3 Temperature sensor A coil temperature sensor has failed or come unplugged.](https://rangerepair.center/error-codes/zline-f3/)
- [F/4 Surface elements and induction The power transistor feeding an induction coil is malfunctioning.](https://rangerepair.center/error-codes/zline-f4/)
- [E/1 Surface elements and induction A coil's temperature sensor has seen too much heat.](https://rangerepair.center/error-codes/zline-e1/)
- [E/2 Surface elements and induction The coil's power transistor has overheated.](https://rangerepair.center/error-codes/zline-e2/)
- [E/3 Controls and communication The incoming voltage is too high.](https://rangerepair.center/error-codes/zline-e3/)
- [E/4 Controls and communication The incoming voltage is too low.](https://rangerepair.center/error-codes/zline-e4/)
- [E/5 Temperature sensor A coil sensor has come loose or moved.](https://rangerepair.center/error-codes/zline-e5/)

[ZLINE range repair](https://rangerepair.center/brands/zline/)

### La Cornue range error codes 7 codes

- [E2 Surface elements and induction The electronics under the induction glass have overheated.](https://rangerepair.center/error-codes/la-cornue-e2/)
- [U400 Controls and communication The range has been wired to the supply wrongly.](https://rangerepair.center/error-codes/la-cornue-u400/)
- [Er Surface elements and induction An internal problem that needs a technician.](https://rangerepair.center/error-codes/la-cornue-er/)
- [U Surface elements and induction No pan, or a pan that will not work on induction.](https://rangerepair.center/error-codes/la-cornue-u/)
- [E Surface elements and induction An electronic failure in the induction plate.](https://rangerepair.center/error-codes/la-cornue-e/)
- [H Mode, not a failure Residual heat left in the zone.](https://rangerepair.center/error-codes/la-cornue-h/)
- [L Mode, not a failure The plate's locking function is on.](https://rangerepair.center/error-codes/la-cornue-l/)

[La Cornue range repair](https://rangerepair.center/brands/la-cornue/)

### Whirlpool range error codes 7 codes

- [FEE6 Oven heating The control suspects the bake element in the main oven or its wiring.](https://rangerepair.center/error-codes/whirlpool-fee6/)
- [FEE7 Oven heating The control suspects the broil element in the main oven or its wiring.](https://rangerepair.center/error-codes/whirlpool-fee7/)
- [C81 Surface elements and induction A surface cooking area overheated and switched itself off.](https://rangerepair.center/error-codes/whirlpool-c81-c82-c83/)
- [H Mode, not a failure A cooking area is still too hot to touch.](https://rangerepair.center/error-codes/whirlpool-h/)
- [F8 E0 Fans The oven cooling fan is turning too slowly.](https://rangerepair.center/error-codes/whirlpool-f8-e0/)
- [F5 E5 Door and lock Self-clean did not get hot enough within 30 minutes, often from a poor door seal.](https://rangerepair.center/error-codes/whirlpool-f5-e5/)
- [F3 E2 Temperature sensor The control distrusts a temperature sensor, possibly the warming drawer one.](https://rangerepair.center/error-codes/whirlpool-f3-e2/)

[Whirlpool range repair](https://rangerepair.center/brands/whirlpool/)

### Fulgor Milano range error codes 6 codes

- [F03 Door and lock The oven door latch mechanism has a problem.](https://rangerepair.center/error-codes/fulgor-milano-f03/)
- [F15 Controls and communication An oven knob sat between OFF and SELF-CLEAN for 30 seconds.](https://rangerepair.center/error-codes/fulgor-milano-f15/)
- [F17 Controls and communication A follow-on to F15.](https://rangerepair.center/error-codes/fulgor-milano-f17/)
- [F13 Mode, not a failure The meat probe is plugged in for a mode that cannot use it.](https://rangerepair.center/error-codes/fulgor-milano-f13/)
- [Fan failure Fans The cooling-fan system has a problem.](https://rangerepair.center/error-codes/fulgor-milano-fan-failure/)
- [L Mode, not a failure The induction control lock is on.](https://rangerepair.center/error-codes/fulgor-milano-l/)

[Fulgor Milano range repair](https://rangerepair.center/brands/fulgor-milano/)

### KitchenAid range error codes 6 codes

- [Blinking amber light Controls and communication The commercial-style range is signaling an error with amber lights and a tone.](https://rangerepair.center/error-codes/kitchenaid-amber-light/)
- [F0E0 Mode, not a failure A clean result: the system check found nothing wrong.](https://rangerepair.center/error-codes/kitchenaid-f0e0/)
- [Blinking Start button Mode, not a failure Start was pressed before it was ready, or the oven is heading to a new temperature.](https://rangerepair.center/error-codes/kitchenaid-white-start-blink/)
- [F7 E5 Fans The control reports a problem with the cooling fan circuit.](https://rangerepair.center/error-codes/kitchenaid-f7-e5/)
- [F2 E0 Controls and communication The keypad or user interface is not talking properly to the control.](https://rangerepair.center/error-codes/kitchenaid-f2-e0/)
- [F3 E3 Temperature sensor The oven temperature sensor or its wiring reads out of range.](https://rangerepair.center/error-codes/kitchenaid-f3-e3/)

[KitchenAid range repair](https://rangerepair.center/brands/kitchenaid/)

### Maytag range error codes 6 codes

- [Flashing indicator light Controls and communication The glass-top controls think a key is being held down.](https://rangerepair.center/error-codes/maytag-indicator-flashing/)
- [Lock Mode, not a failure Control Lock is on, so the touch controls ignore you.](https://rangerepair.center/error-codes/maytag-lock/)
- [ES Mode, not a failure Energy Save has put the display to sleep.](https://rangerepair.center/error-codes/maytag-es/)
- [1c1c Controls and communication The user interface or keypad, or its wiring, is suspect.](https://rangerepair.center/error-codes/maytag-1c1c/)
- [3d11 Temperature sensor The oven temperature sensor, the control or the wiring gives a bad reading.](https://rangerepair.center/error-codes/maytag-3d11/)
- [F8 E2 Fans The oven cooling fan is spinning faster than it should.](https://rangerepair.center/error-codes/maytag-f8-e2/)

[Maytag range repair](https://rangerepair.center/brands/maytag/)

### GE range error codes 5 codes

- [F0 Controls and communication The keypanel has a problem and often needs replacing.](https://rangerepair.center/error-codes/ge-f0/)
- [F2 Oven heating The oven overheated past a preset limit.](https://rangerepair.center/error-codes/ge-f2/)
- [F3 Temperature sensor GE says the oven sensor is the usual culprit.](https://rangerepair.center/error-codes/ge-f3/)
- [F9 Door and lock Something in the door lock circuit has failed.](https://rangerepair.center/error-codes/ge-f9/)
- [DOOR LOCK Mode, not a failure Self-clean was selected while the oven door was open.](https://rangerepair.center/error-codes/ge-door-lock-flashes/)

[GE range repair](https://rangerepair.center/brands/ge/)

### GE Profile range error codes 5 codes

- [Flashing power setting Surface elements and induction The induction element does not accept the pan.](https://rangerepair.center/error-codes/ge-profile-flashing-power/)
- [F4 Temperature sensor The control no longer trusts the oven temperature sensor.](https://rangerepair.center/error-codes/ge-profile-f4/)
- [FC Door and lock GE reports a failed part in the lock circuit of the oven door.](https://rangerepair.center/error-codes/ge-profile-fc/)
- [HOT Mode, not a failure The oven is too warm to start Steam Clean.](https://rangerepair.center/error-codes/ge-profile-hot/)
- [F8 Controls and communication The electronic control usually needs replacing.](https://rangerepair.center/error-codes/ge-profile-f8/)

[GE Profile range repair](https://rangerepair.center/brands/ge-profile/)

### Kenmore range error codes 5 codes

- [Er- Controls and communication The oven control has logged a function error code.](https://rangerepair.center/error-codes/kenmore-er/)
- [Hot Mode, not a failure The oven is too warm for Steam Clean to start.](https://rangerepair.center/error-codes/kenmore-hot/)
- [H Mode, not a failure An induction cooking zone is still too hot to touch.](https://rangerepair.center/error-codes/kenmore-h/)
- [LOC Mode, not a failure The control panel lock is on.](https://rangerepair.center/error-codes/kenmore-loc/)
- [SAbb Mode, not a failure The Sabbath setting is selected in the settings menu.](https://rangerepair.center/error-codes/kenmore-sabb/)

[Kenmore range repair](https://rangerepair.center/brands/kenmore/)

### Bertazzoni range error codes 4 codes

- [H Mode, not a failure The zone is off but the glass is still very hot.](https://rangerepair.center/error-codes/bertazzoni-h/)
- [L Mode, not a failure The child lock is on.](https://rangerepair.center/error-codes/bertazzoni-l/)
- [A Mode, not a failure The heating accelerator is running.](https://rangerepair.center/error-codes/bertazzoni-a/)
- [Showroom Mode, not a failure The display works but the oven is set not to heat.](https://rangerepair.center/error-codes/bertazzoni-showroom/)

[Bertazzoni range repair](https://rangerepair.center/brands/bertazzoni/)

### Café range error codes 4 codes

- [Flashing ON indicator Surface elements and induction The element did not find a pan it can heat.](https://rangerepair.center/error-codes/cafe-on-indicator-flash/)
- [FD Temperature sensor The meat probe or its receptacle likely needs replacing.](https://rangerepair.center/error-codes/cafe-fd/)
- [F7 Controls and communication GE Appliances ties this code to the touch keypanel.](https://rangerepair.center/error-codes/cafe-f7/)
- [CLOSE DOOR Mode, not a failure The door is open during broil or self-clean, so the oven waits.](https://rangerepair.center/error-codes/cafe-close-door/)

[Café range repair](https://rangerepair.center/brands/cafe/)

### Fisher & Paykel range error codes 4 codes

- [A1 Oven heating The range's oven has overheated and paused itself.](https://rangerepair.center/error-codes/fisher-and-paykel-range-a1/)
- [A2 Door and lock The door would not lock at the start of self-clean.](https://rangerepair.center/error-codes/fisher-and-paykel-range-a2/)
- [A3 Door and lock The door would not unlock after self-clean finished.](https://rangerepair.center/error-codes/fisher-and-paykel-range-a3/)
- [F + number Controls and communication An F followed by a number is a technical problem that needs service.](https://rangerepair.center/error-codes/fisher-and-paykel-range-f-number/)

[Fisher & Paykel range repair](https://rangerepair.center/brands/fisher-and-paykel/)

### Monogram range error codes 3 codes

- [Err turn surface burners off Mode, not a failure A burner was turned on while self-clean is running.](https://rangerepair.center/error-codes/monogram-err-turn-surface-burners-off/)
- [Probe Mode, not a failure A probe is plugged in and the oven wants a target temperature.](https://rangerepair.center/error-codes/monogram-probe/)
- [F- and a number Controls and communication An F code means the oven control recorded a function error.](https://rangerepair.center/error-codes/monogram-f-code/)

[Monogram range repair](https://rangerepair.center/brands/monogram/)

### Smeg range error codes 2 codes

- [ERR Controls and communication The oven control has logged an error Smeg does not explain.](https://rangerepair.center/error-codes/smeg-err/)
- [Pre-heating light flashing Mode, not a failure The oven is holding its set temperature.](https://rangerepair.center/error-codes/smeg-preheat-light-flashing/)

[Smeg range repair](https://rangerepair.center/brands/smeg/)

### Only confirmed codes

Every code here is taken from the manufacturer's own documentation, never from a forum or a parts listing. If yours is not listed, book with the exact characters and the full model number, and we will tell you whether it is one we take.

## Three things before you look it up.

A code is a lead, not a verdict. These decide whether the answer you find will be any use.

01

### The code, character by character

Write down every letter and number in order, and note whether it blinks or beeps. Photograph it before anything else, since turning a knob or switching the breaker can wipe it.

02

### The model number, all of it

It is usually on a label behind the storage drawer or around the oven door opening. One code can mean an igniter on one make and a door lock on another.

03

### Any smell of gas or scorching?

Your answer decides whether you shut the range off and head outside right now, or book the next free slot.

## What each kind of code means.

Codes fall into a handful of families. The family says more about the likely repair than the characters do — and one of them is not a repair at all.

[How to read a code](https://rangerepair.center/problems/range-error-code/)

### Mode, not a failure

51 codes

Something the range was told to do, or a state it chose on purpose — a control lock, a Sabbath setting, a demo mode that lights the display but never heats, a pan warning on an induction zone. Nothing has worn out, and no part is needed.

[S](https://rangerepair.center/error-codes/aga-s/) [H](https://rangerepair.center/error-codes/aga-h/) [L](https://rangerepair.center/error-codes/aga-l/) [H](https://rangerepair.center/error-codes/bertazzoni-h/) [L](https://rangerepair.center/error-codes/bertazzoni-l/) [A](https://rangerepair.center/error-codes/bertazzoni-a/) [Showroom](https://rangerepair.center/error-codes/bertazzoni-showroom/) [ERR/toP](https://rangerepair.center/error-codes/bosch-err-top/) [dE](https://rangerepair.center/error-codes/bosch-de/) [F8](https://rangerepair.center/error-codes/bosch-f8/) [CLOSE DOOR](https://rangerepair.center/error-codes/cafe-close-door/) [5d](https://rangerepair.center/error-codes/electrolux-5d/) [–](https://rangerepair.center/error-codes/frigidaire-dash/) [F13](https://rangerepair.center/error-codes/fulgor-milano-f13/) [L](https://rangerepair.center/error-codes/fulgor-milano-l/) [HOT](https://rangerepair.center/error-codes/ge-profile-hot/) [DOOR LOCK](https://rangerepair.center/error-codes/ge-door-lock-flashes/) [ER03](https://rangerepair.center/error-codes/hestan-smart-burner-er03/) [H](https://rangerepair.center/error-codes/ilve-h/) [LLLL](https://rangerepair.center/error-codes/ilve-llll/) [ES](https://rangerepair.center/error-codes/jennair-range-es/) [F0E0](https://rangerepair.center/error-codes/jennair-pro-f0e0/) [Hot](https://rangerepair.center/error-codes/kenmore-hot/) [H](https://rangerepair.center/error-codes/kenmore-h/) [LOC](https://rangerepair.center/error-codes/kenmore-loc/) [SAbb](https://rangerepair.center/error-codes/kenmore-sabb/) [F0E0](https://rangerepair.center/error-codes/kitchenaid-f0e0/) [Blinking Start button](https://rangerepair.center/error-codes/kitchenaid-white-start-blink/) [H](https://rangerepair.center/error-codes/la-cornue-h/) [L](https://rangerepair.center/error-codes/la-cornue-l/) [HS](https://rangerepair.center/error-codes/lg-hs/) [PF](https://rangerepair.center/error-codes/lg-pf/) [Sb](https://rangerepair.center/error-codes/lg-sb/) [Lock](https://rangerepair.center/error-codes/maytag-lock/) [ES](https://rangerepair.center/error-codes/maytag-es/) [Demo Mode](https://rangerepair.center/error-codes/miele-demo-mode/) [Maximum operating duration reached](https://rangerepair.center/error-codes/miele-maximum-operating-duration/) [Power failure - Program cancelled](https://rangerepair.center/error-codes/miele-power-failure/) [System Lock](https://rangerepair.center/error-codes/miele-system-lock/) [Err turn surface burners off](https://rangerepair.center/error-codes/monogram-err-turn-surface-burners-off/) [Probe](https://rangerepair.center/error-codes/monogram-probe/) [tESt](https://rangerepair.center/error-codes/samsung-test/) [-dC-](https://rangerepair.center/error-codes/samsung-dc/) [Cooktop in use](https://rangerepair.center/error-codes/samsung-top-in-use/) [C-10](https://rangerepair.center/error-codes/samsung-c-10/) [Loc](https://rangerepair.center/error-codes/sks-loc/) [Pre-heating light flashing](https://rangerepair.center/error-codes/smeg-preheat-light-flashing/) [dE](https://rangerepair.center/error-codes/thermador-de/) [F8](https://rangerepair.center/error-codes/thermador-f8/) [H](https://rangerepair.center/error-codes/whirlpool-h/) [PF](https://rangerepair.center/error-codes/wolf-df-pf/)

Usually leads to

No repair — the setting is changed back

Shows up as

[Range Control Panel Not Responding](https://rangerepair.center/problems/control-panel-not-responding/) [Range Oven Not Heating](https://rangerepair.center/problems/range-oven-not-heating/) [Induction Range Not Detecting Pan](https://rangerepair.center/problems/induction-not-detecting-pan/) [Range Error Code](https://rangerepair.center/problems/range-error-code/)

### Burners and ignition

3 codes

A burner was asked to light and the range did not sense a flame, or the spark kept firing after the flame was there. Moisture or food in the igniter and a cap sitting out of place are ruled out before the spark module or a switch is replaced. A smell of gas outranks any code: leave the house and phone the gas utility from outside.

[ER01](https://rangerepair.center/error-codes/hestan-smart-burner-er01/) [ER05](https://rangerepair.center/error-codes/hestan-smart-burner-er05/) [ER06](https://rangerepair.center/error-codes/hestan-smart-burner-er06/)

Usually leads to

[Burner and igniter repair](https://rangerepair.center/services/burner-and-igniter-repair/)

Shows up as

[Range Burner Won't Light](https://rangerepair.center/problems/burner-wont-light/) [Range Burner Keeps Clicking](https://rangerepair.center/problems/burner-keeps-clicking/) [Uneven Range Burner Flame](https://rangerepair.center/problems/burner-flame-uneven/) [Range Gas Smell](https://rangerepair.center/problems/range-gas-smell/)

### Surface elements and induction

38 codes

A radiant element, a coil or an induction zone did not heat the way the control expected, or ran hotter than it should. The pan, the switch behind the knob and the wiring to the element come first; on induction, the power board and the coil under the glass are checked next. A zone that will not switch off, or a crack in the glass, means the breaker goes off before anything else.

[E2](https://rangerepair.center/error-codes/aga-e2/) [Er](https://rangerepair.center/error-codes/aga-er/) [E6](https://rangerepair.center/error-codes/aga-e6/) [E2](https://rangerepair.center/error-codes/bluestar-induction-e2/) [E6](https://rangerepair.center/error-codes/bluestar-induction-e6/) [F1](https://rangerepair.center/error-codes/bosch-f1/) [F2](https://rangerepair.center/error-codes/bosch-f2/) [F5](https://rangerepair.center/error-codes/bosch-f5/) [Flashing ON indicator](https://rangerepair.center/error-codes/cafe-on-indicator-flash/) [F40](https://rangerepair.center/error-codes/electrolux-f40/) [F40](https://rangerepair.center/error-codes/frigidaire-f40/) [Flashing power setting](https://rangerepair.center/error-codes/ge-profile-flashing-power/) [E2](https://rangerepair.center/error-codes/hestan-induction-e2/) [E6](https://rangerepair.center/error-codes/hestan-induction-e6/) [U 400](https://rangerepair.center/error-codes/hestan-induction-u400/) [E5](https://rangerepair.center/error-codes/ilve-e5-e6/) [E](https://rangerepair.center/error-codes/ilve-e/) [F](https://rangerepair.center/error-codes/ilve-f/) [U](https://rangerepair.center/error-codes/ilve-u/) [C81](https://rangerepair.center/error-codes/jennair-range-c81/) [E2](https://rangerepair.center/error-codes/la-cornue-e2/) [Er](https://rangerepair.center/error-codes/la-cornue-er/) [U](https://rangerepair.center/error-codes/la-cornue-u/) [E](https://rangerepair.center/error-codes/la-cornue-e/) [F33](https://rangerepair.center/error-codes/lg-f33/) [F51](https://rangerepair.center/error-codes/lg-f51/) [Underlined u](https://rangerepair.center/error-codes/samsung-underlined-u/) [F1~F15](https://rangerepair.center/error-codes/sks-induction-knob-f1-f15/) [F33~F45](https://rangerepair.center/error-codes/sks-f33-f45/) [F1](https://rangerepair.center/error-codes/thermador-f1/) [F2](https://rangerepair.center/error-codes/thermador-f2/) [F4](https://rangerepair.center/error-codes/thermador-f4/) [F5](https://rangerepair.center/error-codes/thermador-f5/) [C81](https://rangerepair.center/error-codes/whirlpool-c81-c82-c83/) [E2](https://rangerepair.center/error-codes/wolf-ir-e2/) [F/4](https://rangerepair.center/error-codes/zline-f4/) [E/1](https://rangerepair.center/error-codes/zline-e1/) [E/2](https://rangerepair.center/error-codes/zline-e2/)

Usually leads to

[Surface element and glass top repair](https://rangerepair.center/services/surface-element-and-glass-top-repair/)

Shows up as

[Range Surface Element Not Heating](https://rangerepair.center/problems/surface-element-not-heating/) [Induction Range Not Detecting Pan](https://rangerepair.center/problems/induction-not-detecting-pan/) [Range Burner Won't Turn Off](https://rangerepair.center/problems/burner-wont-turn-off/) [Range Glass Top Cracked](https://rangerepair.center/problems/glass-top-cracked/)

### Oven heating

18 codes

The oven under the burners called for heat and the cavity did not warm the way the control planned. On an electric oven a bake or broil element that has burned open is the usual cause; on a gas oven the igniter and the valve it opens come first. The wiring and the relay are checked before the board takes the blame.

[010-014](https://rangerepair.center/error-codes/aga-010-014/) [130-136](https://rangerepair.center/error-codes/aga-130-136/) [F80](https://rangerepair.center/error-codes/bluestar-range-f80/) [C-21](https://rangerepair.center/error-codes/dacor-range-c-21/) [C-24](https://rangerepair.center/error-codes/dacor-range-c-24/) [F10](https://rangerepair.center/error-codes/electrolux-f10/) [A1](https://rangerepair.center/error-codes/fisher-and-paykel-range-a1/) [F10](https://rangerepair.center/error-codes/frigidaire-f10/) [F2](https://rangerepair.center/error-codes/ge-f2/) [F9](https://rangerepair.center/error-codes/lg-f9/) [C-21](https://rangerepair.center/error-codes/samsung-c-21/) [C-24](https://rangerepair.center/error-codes/samsung-c-24/) [C-25](https://rangerepair.center/error-codes/samsung-c-25/) [F-9](https://rangerepair.center/error-codes/sks-f-9/) [FEE6](https://rangerepair.center/error-codes/whirlpool-fee6/) [FEE7](https://rangerepair.center/error-codes/whirlpool-fee7/) [02](https://rangerepair.center/error-codes/wolf-df-02/) [0E](https://rangerepair.center/error-codes/wolf-df-0e/)

Usually leads to

[Bake and broil elements](https://rangerepair.center/services/bake-and-broil-element-repair/)

Shows up as

[Range Oven Not Heating](https://rangerepair.center/problems/range-oven-not-heating/) [Range Broiler Not Working](https://rangerepair.center/problems/range-broiler-not-working/) [Range Oven Temperature Wrong](https://rangerepair.center/problems/range-oven-temperature-wrong/)

### Temperature sensor

30 codes

The oven sensor sent a reading the control would not accept, or one that climbed well past the setting. A loose plug or a sensor that has drifted is ruled out before the control board, and a temperature that keeps rising means the range is switched off at the breaker first.

[007](https://rangerepair.center/error-codes/aga-007/) [020-024](https://rangerepair.center/error-codes/aga-020-024/) [060-100](https://rangerepair.center/error-codes/aga-060-100/) [120-124](https://rangerepair.center/error-codes/aga-120-124/) [F40](https://rangerepair.center/error-codes/bluestar-range-f40/) [F50](https://rangerepair.center/error-codes/bluestar-range-f50/) [e101](https://rangerepair.center/error-codes/bosch-e101/) [FD](https://rangerepair.center/error-codes/cafe-fd/) [C-20](https://rangerepair.center/error-codes/dacor-range-c-20/) [C-23](https://rangerepair.center/error-codes/dacor-range-c-23/) [C-70](https://rangerepair.center/error-codes/dacor-range-c-70/) [F30](https://rangerepair.center/error-codes/electrolux-f30/) [F30](https://rangerepair.center/error-codes/frigidaire-f30/) [F31](https://rangerepair.center/error-codes/frigidaire-f31/) [F4](https://rangerepair.center/error-codes/ge-profile-f4/) [F3](https://rangerepair.center/error-codes/ge-f3/) [E9](https://rangerepair.center/error-codes/ilve-e9/) [F3-1](https://rangerepair.center/error-codes/jennair-range-f3-1/) [F8](https://rangerepair.center/error-codes/jennair-range-f8/) [F3 E3](https://rangerepair.center/error-codes/kitchenaid-f3-e3/) [F1](https://rangerepair.center/error-codes/lg-f1/) [F4](https://rangerepair.center/error-codes/lg-f4/) [3d11](https://rangerepair.center/error-codes/maytag-3d11/) [No signal to the probe](https://rangerepair.center/error-codes/miele-probe-no-signal/) [C-20](https://rangerepair.center/error-codes/samsung-c-20/) [C-30](https://rangerepair.center/error-codes/samsung-c-30/) [F3 E2](https://rangerepair.center/error-codes/whirlpool-f3-e2/) [03](https://rangerepair.center/error-codes/wolf-df-03/) [F/3](https://rangerepair.center/error-codes/zline-f3/) [E/5](https://rangerepair.center/error-codes/zline-e5/)

Usually leads to

[Temperature sensor and thermostat repair](https://rangerepair.center/services/temperature-sensor-and-thermostat-repair/)

Shows up as

[Range Oven Temperature Wrong](https://rangerepair.center/problems/range-oven-temperature-wrong/) [Range Oven Not Heating](https://rangerepair.center/problems/range-oven-not-heating/) [Range Error Code](https://rangerepair.center/problems/range-error-code/)

### Door and lock

20 codes

The oven door lock did not move to where the control sent it, or its switch reported the wrong position. It shows up most around self-clean; the latch, its switches, the hinges and how squarely the door closes are looked at before the lock motor is changed.

[139](https://rangerepair.center/error-codes/aga-139/) [e126](https://rangerepair.center/error-codes/bosch-e126/) [C-d1](https://rangerepair.center/error-codes/dacor-range-c-d1/) [F90](https://rangerepair.center/error-codes/electrolux-f90/) [A2](https://rangerepair.center/error-codes/fisher-and-paykel-range-a2/) [A3](https://rangerepair.center/error-codes/fisher-and-paykel-range-a3/) [F90](https://rangerepair.center/error-codes/frigidaire-f90/) [F03](https://rangerepair.center/error-codes/fulgor-milano-f03/) [FC](https://rangerepair.center/error-codes/ge-profile-fc/) [F9](https://rangerepair.center/error-codes/ge-f9/) [F5](https://rangerepair.center/error-codes/jennair-range-f5/) [F7 E0](https://rangerepair.center/error-codes/jennair-range-f7-e0/) [F5E0](https://rangerepair.center/error-codes/jennair-pro-f5e0/) [F10](https://rangerepair.center/error-codes/lg-f10/) [F32](https://rangerepair.center/error-codes/miele-f32/) [F33](https://rangerepair.center/error-codes/miele-f33/) [C-d1](https://rangerepair.center/error-codes/samsung-c-d1/) [door](https://rangerepair.center/error-codes/samsung-door/) [F5 E5](https://rangerepair.center/error-codes/whirlpool-f5-e5/) [01](https://rangerepair.center/error-codes/wolf-df-01/)

Usually leads to

[Door hinge, gasket and lock repair](https://rangerepair.center/services/door-hinge-gasket-and-lock-repair/)

Shows up as

[Range Self-Clean Problems](https://rangerepair.center/problems/range-self-clean-problems/) [Range Oven Door Won't Close](https://rangerepair.center/problems/range-door-wont-close/) [Range Error Code](https://rangerepair.center/problems/range-error-code/)

### Fans

12 codes

The convection fan behind the oven's back wall, or the cooling fan that keeps heat away from the controls, did not spin as fast as the control expected. Grease on the blade and a loose plug are checked first; a tired motor, and on the cooling side a thermal fuse, come after.

[F60](https://rangerepair.center/error-codes/bluestar-range-f60/) [E8](https://rangerepair.center/error-codes/bluestar-induction-e8/) [C-A2](https://rangerepair.center/error-codes/dacor-range-c-a2/) [Fan failure](https://rangerepair.center/error-codes/fulgor-milano-fan-failure/) [E8](https://rangerepair.center/error-codes/hestan-induction-e8/) [F7 E5](https://rangerepair.center/error-codes/kitchenaid-f7-e5/) [F17](https://rangerepair.center/error-codes/lg-f17/) [F27](https://rangerepair.center/error-codes/lg-f27/) [F8 E2](https://rangerepair.center/error-codes/maytag-f8-e2/) [F8 E0](https://rangerepair.center/error-codes/whirlpool-f8-e0/) [COOL FAN](https://rangerepair.center/error-codes/wolf-df-cool-fan/) [E8](https://rangerepair.center/error-codes/wolf-ir-e8/)

Usually leads to

[Convection fan repair](https://rangerepair.center/services/convection-fan-repair/)

Shows up as

[Range Oven Temperature Wrong](https://rangerepair.center/problems/range-oven-temperature-wrong/) [Range Oven Not Heating](https://rangerepair.center/problems/range-oven-not-heating/) [Range Control Panel Not Responding](https://rangerepair.center/problems/control-panel-not-responding/)

### Controls and communication

70 codes

The display, the main board or the induction power board lost contact with one another, or one of them failed its own self-check. A power dip, a loose cable or moisture from a boil-over is ruled out before a board is replaced, and a range that keeps heating while this code shows is switched off at the breaker.

[FE](https://rangerepair.center/error-codes/aga-fe/) [VE](https://rangerepair.center/error-codes/aga-ve/) [CE](https://rangerepair.center/error-codes/aga-ce/) [110-116](https://rangerepair.center/error-codes/aga-110-116/) [140](https://rangerepair.center/error-codes/aga-140/) [150-156](https://rangerepair.center/error-codes/aga-150-156/) [159](https://rangerepair.center/error-codes/aga-159/) [U400](https://rangerepair.center/error-codes/aga-u400/) [F20](https://rangerepair.center/error-codes/bluestar-range-f20/) [Er47](https://rangerepair.center/error-codes/bluestar-induction-er47/) [e005](https://rangerepair.center/error-codes/bosch-e005/) [e011](https://rangerepair.center/error-codes/bosch-e011/) [E302](https://rangerepair.center/error-codes/bosch-e302/) [e310](https://rangerepair.center/error-codes/bosch-e310/) [E9000](https://rangerepair.center/error-codes/bosch-e9000/) [E9011](https://rangerepair.center/error-codes/bosch-e9011/) [F7](https://rangerepair.center/error-codes/cafe-f7/) [C-d0](https://rangerepair.center/error-codes/dacor-range-c-d0/) [C-F0](https://rangerepair.center/error-codes/dacor-range-c-f0/) [C-F2](https://rangerepair.center/error-codes/dacor-range-c-f2/) [Err](https://rangerepair.center/error-codes/electrolux-err-number/) [F3](https://rangerepair.center/error-codes/electrolux-f3/) [F1](https://rangerepair.center/error-codes/electrolux-f1/) [F + number](https://rangerepair.center/error-codes/fisher-and-paykel-range-f-number/) [F1](https://rangerepair.center/error-codes/frigidaire-f1/) [F12](https://rangerepair.center/error-codes/frigidaire-f12/) [F3](https://rangerepair.center/error-codes/frigidaire-f3/) [F15](https://rangerepair.center/error-codes/fulgor-milano-f15/) [F17](https://rangerepair.center/error-codes/fulgor-milano-f17/) [F8](https://rangerepair.center/error-codes/ge-profile-f8/) [F0](https://rangerepair.center/error-codes/ge-f0/) [ERR04](https://rangerepair.center/error-codes/hestan-range-err04/) [ERR20](https://rangerepair.center/error-codes/hestan-range-err20/) [Er 03](https://rangerepair.center/error-codes/hestan-induction-er03/) [Er 47](https://rangerepair.center/error-codes/hestan-induction-er47/) [E47](https://rangerepair.center/error-codes/ilve-e47/) [F6](https://rangerepair.center/error-codes/jennair-range-f6/) [F9E0](https://rangerepair.center/error-codes/jennair-pro-f9e0/) [Blinking amber lights](https://rangerepair.center/error-codes/jennair-pro-amber-lights/) [Er-](https://rangerepair.center/error-codes/kenmore-er/) [Blinking amber light](https://rangerepair.center/error-codes/kitchenaid-amber-light/) [F2 E0](https://rangerepair.center/error-codes/kitchenaid-f2-e0/) [U400](https://rangerepair.center/error-codes/la-cornue-u400/) [F3](https://rangerepair.center/error-codes/lg-f3/) [F11](https://rangerepair.center/error-codes/lg-f11/) [F42](https://rangerepair.center/error-codes/lg-f42/) [Flashing indicator light](https://rangerepair.center/error-codes/maytag-indicator-flashing/) [1c1c](https://rangerepair.center/error-codes/maytag-1c1c/) [Fault](https://rangerepair.center/error-codes/miele-unlisted-code/) [F- and a number](https://rangerepair.center/error-codes/monogram-f-code/) [C-d0](https://rangerepair.center/error-codes/samsung-c-d0/) [C-F0](https://rangerepair.center/error-codes/samsung-c-f0/) [bAd LinE](https://rangerepair.center/error-codes/samsung-bad-line/) [F1~F25](https://rangerepair.center/error-codes/sks-f1-f25/) [F51~F59](https://rangerepair.center/error-codes/sks-f51-f59/) [F62](https://rangerepair.center/error-codes/sks-f62/) [F-3](https://rangerepair.center/error-codes/sks-f-3/) [ERR](https://rangerepair.center/error-codes/smeg-err/) [E](https://rangerepair.center/error-codes/thermador-e-number/) [E0211](https://rangerepair.center/error-codes/thermador-e0211/) [E7010](https://rangerepair.center/error-codes/thermador-e7010/) [E9000](https://rangerepair.center/error-codes/thermador-e9000/) [U400](https://rangerepair.center/error-codes/thermador-u400/) [COMM ERR](https://rangerepair.center/error-codes/wolf-df-comm-err/) [ERR OC](https://rangerepair.center/error-codes/wolf-df-err-oc/) [03](https://rangerepair.center/error-codes/wolf-ir-03/) [47](https://rangerepair.center/error-codes/wolf-ir-47/) [F/1](https://rangerepair.center/error-codes/zline-f1/) [E/3](https://rangerepair.center/error-codes/zline-e3/) [E/4](https://rangerepair.center/error-codes/zline-e4/)

Usually leads to

[Knobs, switches and controls](https://rangerepair.center/services/knobs-switches-and-controls/)

Shows up as

[Range Control Panel Not Responding](https://rangerepair.center/problems/control-panel-not-responding/) [Range Error Code](https://rangerepair.center/problems/range-error-code/) [Range Burner Won't Turn Off](https://rangerepair.center/problems/burner-wont-turn-off/)

For the heart of your home.

## Questions about the codes.

### The code on my range is not listed here. What next?

It only means we have not documented it yet; a code is added when the maker's own material explains it. Write the characters down, note whether they blink, and enter them in the booking form so the technician can check them against your model.

### Does a range code mean the same on every brand?

No. A code that names an oven sensor on one make can point to a door lock or a board on another, and some makers changed meanings from one generation to the next. Always read a code against the make and, where it counts, the exact model.

### Can I clear a range code myself?

Turning the range off at its breaker for a few minutes sometimes clears one, and a code that never returns was often a brief power dip. A code that keeps coming back is reporting a real problem. If a burner, element or the oven stays on while a code shows, keep the breaker off and book instead of resetting.

### The range shows a code but still cooks. Is anything broken?

Maybe not. Some codes people look up are settings or locks — a control lock, a Sabbath setting, a demo mode, a pan warning on an induction zone — that change how the range acts without a part failing. Each code page flags those and says how to turn them off.

---

**[Read on the site: Range Error Codes — What They Mean | RangeRepair.center](https://rangerepair.center/error-codes/)**

**[Book a visit with RangeRepair.center](https://rangerepair.center/schedule/)**